Analysis of Ventilated Disc Brake Using Ansys with Computer Aided Manufacturing

Ashok Kumar Madan; Saksham Dabas; Sanchit Behal; Vishesh Chhabra

doi:https://doi.org/10.51976/ijari.1042204

Submit Manuscript Login / Register Subscribe

Home Page

Editorial Advisory Board

Mission, Aims & Scope

Current Issue

Analysis of Ventilated Disc Brake Using Ansys with Computer Aided Manufacturing

Ashok Kumar Madan, Saksham Dabas, Sanchit Behal, Vishesh Chhabra

Vol 10 , Issue 4 , October - December 2022 | Pages: 22-33 | Research Paper

https://doi.org/10.51976/ijari.1042204

Received: August 11, 2022 | Revised: November 25, 2022 | Accepted: December 05, 2022 | Published Online: December 15, 2022

Author Details ( * ) denotes Corresponding author

1. Ashok Kumar Madan, Department of Mechanical Engineering, Delhi Technological University, Dehi, Dehi, India

2. Saksham Dabas, Department of Mechanical Engineering, Delhi Technological University, Dehi, Dehi, India

3. * Sanchit Behal, Department of Mechanical Engineering, Delhi Technological University, Dehi, Dehi, India (sanchitbehal_2k19ae054@dtu.ac.in)

4. Vishesh Chhabra, Department of Mechanical Engineering, Delhi Technological University, Dehi, Dehi, India

Safety is the most important parameter while developing a modern vehicle. A vehicle capable of high acceleration must decelerate quickly as well. Disc brakes are used in modern vehicles to reduce stopping distance. On application of brakes, the disc is subjected to thermal & structural stresses. The brakes fail to slow down or stop the vehicle if they become too hot. In this study, we attempt to understand the existing disc brake rotors in use in the automobile industry and improve on their design in order to enhance heat dissipation. The currently used disc brakes are studied to understand their design. This knowledge is further used to design a useful disc brake. The aim of this paper is to improve heat transfer rate by designing disc rotors and selecting suitable material.

Keywords

Ansys; Solidworks; Thermal Analysis; Ventilated Disc Brake.

Abebe, L., Nallamothu, R. B., Subrahmanyam, K. H. S., Nallamothu, S. K., & Nallamothu, A. K. (2016). Thermal analysis of disc brake made of different materials. system, 3, 4.

Manjunath, T. V., & Suresh, P. M. (2013). Structural and thermal analysis of rotor disc of disc brake. International journal of innovative research in science, Engineering and Technology, 2(12), 7741-7749.

Belhocine, A., & Bouchetara, M. (2013). Investigation of temperature and thermal stress in ventilated disc brake based on 3D thermomechanical coupling model. Ain Shams Engineering Journal, 4(3), 475-483.

Satope, S., Bote, A. K., & Rawool, S. D. (2017). Thermal analysis of disc brake. Int. J. Innov. Res. Sci. Technol, 3, 68-73.

Alam, S. E., Vidhyadhar, Y., Sharma, P., & Jain, A. (2015). Thermal analysis of disc brakes rotor: a comparative report. Journal of Information Sciences and Computing Technologies, 3(2), 196-200.

Singh Chouhan, Y., & Tiwari, S. (2020, March). Static structural and thermal analysis of disc brake pad model. In IOP conference series: materials science and engineering (Vol. 810, No. 1, p. 012073). IOP Publishing.

Pradhan S., M. Santhosh, Rithvik P. Modelling and analysis of ventilated disc brakes using Creo and FEA Software. (Vol. 10, VI, June 2022)

Chandana, Y. V. N., & Reddy, K. P. (2017). Transient thermal analysis of AlSiCp composite disc brake. Int. J. Comput. Eng. Res, 7, 12.

E.E. Reber, R.L. Michell, and C.J. Carter, “Oxygen Absorption in the Earth’s Atmosphere,” Technical Report TR-0200 (420-46)-3, Aerospace Corp., Los Angeles, Calif., Nov. 1988. (Technical report with report number)

L. Hubert and P. Arabie, “Comparing Partitions,” J. Classification, vol. 2, no. 4, pp. 193-218, Apr. 1985. (Journal or magazine citation)

R.J. Vidmar, “On the Use of Atmospheric Plasmas as Electromagnetic Reflectors,” IEEE Trans. Plasma Science, vol. 21, no. 3, pp. 876-880, available at http://www.halcyon.com/pub/journals/21ps03-vidmar, Aug. 1992. (URL for Transaction, journal, or magazine)

J.M.P. Martinez, R.B. Llavori, M.J.A. Cabo, and T.B. Pedersen, "Integrating Data Warehouses with Web Data: A Survey," IEEE Trans. Knowledge and Data Eng., preprint, 21 Dec. 2007, doi:10.1109/TKDE.2007.190746.(PrePrint)

Kumar, G. R., Thriveni, S., Reddy, M. R., & Gowd, G. H. (2014). Design Analysis & Optimization of an Automotive Disc Brake. International Journal of Advanced Engineering Research and Science, 1(3), 24-29.

Jaiswal, R., Jha, A. R., Karki, A., Das, D., Jaiswal, P., Rajgadia, S., ... & Barman, R. N. (2016). Structural and thermal analysis of disc brake using solidworks and ansys. International Journal of Mechanical Engineering and Technology, 7(1), 67-77. Kaiwart, D., & Tembhurne, Y. K. (2017). Comparison of structural and thermal analysis of disc brake using various materials. International journal of thermal engineering, 5(2), 1-10.

Samie, F., & Sheridan, D. C. (1990). Contact analysis for a passenger car disc brake. SAE transactions, 9-15

Bakar, A. A., Ouyang, H., & Hamid, M. K. A. (2005). Modelling and simulation of disc brake contact analysis and squeal.

Li, S., & Yong-Chen, L. (2011, April). The disc brake design and performance analysis. In 2011 International Conference on Consumer Electronics, Communications and Networks (CECNet) (pp. 846-849). IEEE.

Rudramoorthy, S., Vinayagam, M., Karthikeyan, S., & Sathish, T. (2018). Investigation on structural and Thermal analysis of disc brake with Aluminium Metal Matrix Composite. Int. J. Mech. Prod. Eng. Res. Dev.(IJMPERD), 8, 431-440.

Hugar, D. S., & Kadabadi, U. B. (2017). Design and thermal analysis of disc brake for minimizing temperature. International Research Journal of Engineering and Technology (IRJET), 4(07).

Radhakrishnan, C., Yokeswaran, K., Vengadeshprasadh, M., Vishnuhasan, A., Vimalraj, T., & Velusamy, M. (2015). Design and analysis of disc brake with titanium alloy. International Journal of Innovative Science, Engineering & Technology, 2(5), 1044-1050.

Tirovic, M., Sergent, N., Campbell, J., Roberts, P., & Vignjevic, R. (2012). Structural analysis of a commercial vehicle disc brake caliper. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 226(5), 613-622.

Rajkamal, M. D., Samson, T. D. A., Kumar, P. D., & Chithambaravishnu, S. (2018). Structural analysis of disc brake. International Journal of Mechanical Engineering and Technology, 9(3), 846-856.

Mishra, A., & Solanki, P. Computational Analysis & Design Study of Pulsar 150 Front Disc Brake. Journal homepage: www. ijrpr. com ISSN, 2582, 7421.

Jawarikar, P., Khan, S., & Kshirsagar, B. (2016). Structural optimization, thermal and vibration analysis of two wheeler disc brake rotor. Int J Innovative Res Sci Eng, 2(8), 169-186.

Hariram, V., Suresh, R., Reddy, J. S., Reddy, A. B., Nithinkumar, A., Kiran, N. S., ... & Premkumar, T. M. (2021). Thermo-Structural Analysis of Brake Disc-Pad Assembly of an Automotive Braking System. International Journal of Vehicle Structures & Systems, 13(4), 497-504.

Ande, R., Alok, G., & Gulati, P. (2020, December). Fabrication of a Glass Fibre Reinforced Composite Rotor Disc for a bicycle Disc brake. In IOP Conference Series: Materials Science and Engineering (Vol. 981, No. 4, p. 042016). IOP Publishing.

Yadav, C. K., & Joshi, U. K. (2018). Structural And Thermal Analysis Of Rotor Disc: A Review.

Jawahar, H. K. (2021). The Mechanical &Thermal Properties of Various Brake Rotors Materials: A Review.

Mathad, M., Kohli, A., Hombalmath, M., Kakol, B., Patil, A. Y., Kotturshettar, B. B., ... & Patil, V. (2022). Non-Linear structural and thermal analysis of automotive brake disc. Materials Today: Proceedings.

Gupta, N., Bhandwal, M., & Sikarwar, B. S. (2017). Modelling and simulation of brake disc for thermal analysis. Indian Journal of Science and Technology, 10(17), 1-5.

Choi, J. H., Kim, D. H., & Lee, I. (2001). Thermal analysis of automotive disc brake using FFT-FEM. Transactions of the Korean Society of Mechanical Engineers A, 25(8), 1253-1260.

Hugar, D. S., & Kadabadi, U. B. (2017). Design and thermal analysis of disc brake for minimizing temperature. International Research Journal of Engineering and Technology (IRJET), 4(07).

Kumar, A., & Sabarish, R. (2014). Structural and thermal analysis of brake drum. Middle-East Journal of Scientific Research, 20(8), 1012-1016.

Rajappan, R., Gokulakrishnan, J., Gurunathan, G., & Chandrasekar, K. (2021, February). Transient Thermal Analysis of Tungsten Carbide and Hafnium Carbide Disc Brake Rotor. In IOP Conference Series: Materials Science and Engineering (Vol. 1057, No. 1, p. 012020). IOP Publishing.

Jaiswal, R., Jha, A. R., Karki, A., Das, D., Jaiswal, P., Rajgadia, S., ... & Barman, R. N. (2016). Structural and thermal analysis of disc brake using solidworks and ansys. International Journal of Mechanical Engineering and Technology, 7(1), 67-77.

Sarkar, S., Rathod, P. P., & Modi, A. J. (2014). Research Paper on Modeling and Simulation of Disc Brake to Analyse Temperature Distribution using FEA. Int. J. Sci. Res. Dev, 2, 491-494.

Choudhary, A., Jaiswal, A., Kant, A., Zunaid, M., & Ansari, N. A. (2022). Coupled thermal and structural analysis of disc brake rotor with varying angle of rotation of ventilation holes. Materials Today: Proceedings, 56, 834-844.

Ting-Long Ho., 1974. “Effect of frictional heating on brake materials”, Wear, 30(1974) 73-91

Masahiro Kubota., 2000. “Development of lightweight brake disc rotor: A design approach for achieving an optimum thermal, vibration and weight balance.” JASE review 21 (2000) 349-355

Faramarz talati, 2009. “Analysis of heat conduction in a disk brake system”, pinger-Velag2009.

Ziad, 2009. “An investigation of disc brake rotor by FEA.”ISSN: 1985-3157, Vol.3, No. 2, JulyDec 2009.

K. M. Muniswamy, 2013, “Heat transfer enhancement on ventilated brake disk with blade inclination angle variation”, international journal of automotive technology, vol. 14, No. 4, PP.569-577 (2013)

Adam Adamowicz, 2011. “Analysis of disc brake temperature distribution during single braking under non-axisymmetric load”, Apllied thermal engineering 31(2011) 1003-1012.

K. Sowjanya, 2013. “Structural analysis of disk brake rotor”, International Journal of computer trends and technology ( IJCTT)- volume 4 , Issue 7- July 2013

Naga Phaneendra, A., Junaid Razi, S., Kareem L, W. U., Adnan, G. M., & Abdul Ahad, S. M. (2018). Thermal analysis of solid disc brake rotor. International Journal of Mechanical and Production Engineering Research and Development, 8(2), 1039-1048.

Ismael, A. M. (2018). Study of thermal analysis of disc brake rotor for different DISC brakes. International Journal of Mechanical Engineering and Technology, 9(3), 731-738.

Siregar, R., Adhitya, M., Sumarsono, D. A., Nazaruddin, Heryana, G., & Zainuri, F. (2020, May). Study the brake performance of a passenger car based on the temperature that occurs in each brake unit. In AIP Conference Proceedings (Vol. 2227, No. 1, p. 020013). AIP Publishing LLC.

V. Naveen, 2021, Evaluation of Braking Performance of Disc Brake Rotor with different Pillar Ventilation Structures, INTERNATIONAL JOURNAL OF ENGINEERING RESEARCH & TECHNOLOGY (IJERT) Volume 10, Issue 11 (November 2021),

Liu, Shufeng. (2021). Application of Computer Aided 3D CAD Technology in Mechanical Manufacturing and Automation. Journal of Physics: Conference Series. 2143. 012024. 10.1088/1742-6596/2143/1/012024.

Dwivedi, Abhishek. (2013). Role of Computer and Automation in Design and Manufacturing for Mechanical Industries: CAD/CAM. International Journal of Innovative Technology and Exploring Engineering 2278-3075. 3. 174-181.