Material Characteristics, Manufacturing Processes and Product Performance: A Review of Some Experimental Studies

Praveen Pandey; A. K. Chakrabarti

doi:https://doi.org/10.51976/ijari.311542

Submit Manuscript Login / Register Subscribe

Home Page

Editorial Advisory Board

Mission, Aims & Scope

Current Issue

Material Characteristics, Manufacturing Processes and Product Performance: A Review of Some Experimental Studies

Praveen Pandey, A. K. Chakrabarti

Vol 3 , Issue 1 , January - March 2015 | Pages: 246-253 | Research Paper

https://doi.org/10.51976/ijari.311542

Received: January 29, 2015 | Revised: February 25, 2015 | Accepted: February 28, 2015 | Published Online: March 15, 2015

Author Details ( * ) denotes Corresponding author

1. * Praveen Pandey, Department of Mechanical Engineering, PNG University of Technology, Lae, Papua New Guinea (ppande@gmail.com)

2. A. K. Chakrabarti, Ex-Department of Metallurgical & Materials Engineering, IIT Kharagpur, India, Kharagpur, Uttar Pradesh, India

The paper reviews the influence of material characteristics on the manufacturing process and product performance. Results of some previous experimental studies on hot machining, plasma surface coating and laser surface treatment, semi solid heat treatment and clean steel production are compiled, analyzed and discussed. In each case, a correlation is observed between the material characteristics and its response to the manufacturing process.

Keywords

Machining; Grinding; Microstructure; Steel Cleanliness; Diffusion

Miltiadis A. Boboulos, Manufacturing processes and materials exercises, 2010

A. Prodhan, A. K. Chakrabarti, A. B. Chattopadhyay, A study on the machinability of cast Fe-Mn-Si-C alloy, Trans AFS 97 (1989) 501-506.

M. J. Ackerman, Steel slab surface quality prediction using neural networks, M. Eng. thesis, North-West University (South Africa), 2004

K. A. Venugoal, P. P. Chattopadhyay, A. B. Chattopadhyay, A. K. Chakrabarti, Investigation of plasma spray coatings on austenitic, manganese and mild steel, Surface Engineering 15(6), 1999, 465-468

G. S. Reddy, U. K. Chatterjee, A. K. Chakrabarti, A. K. Patra, Characterization of laser beam treated stainless steels, Steel Grips, 8(6), 2010, 941-944

A. Bhattacharya, A. K. Chakrabarti, Modification of a cast Al-Si-Cu alloy by heat treatment in the semisolid state and evaluation of its wear properties, Indian Foundry Journal, 57(5), 2011, 23-28

S. B. Singh, A. K. Chakrabarti, A. B. Chattopadhyay, A study on the effect of inclusion content on the machinability and wear characteristics of 0.24% C steels, Journal of Material Processing Technology, 66, 1997,90-96

V. Torabinejad, A. Zarei-Hanzaki, S. Moemeni, An analysis to the kinetics of austenite recrystallization in Fe-30Mn-5Al steel, Materials and Manufacturing Processes, 28, 2012, 36-41

G. Madhavulu, B. Ahmed, Hot machining process for improved metal removal rates in turning operations, Journal of Material Processing Technology, 44(3-4), 1994, 199-206

W. Xn, Xin Liu, J. Sun, L. Xhang, Finite element simulation and experimental research on electric hot machining, International Journal of Advanced Manufacturing Technology, 66(1-4), 2013, 407-415

P. V. Nazarenko, I. E. Polishchuk, A. E. Ostranitsa, A. Yu. Koval, Structural changes in friction surfaces of plasma-sprayed coatings, Powder Metallurgy and Metal Ceramics, 38(1-2), (1999), 85-88

Ibrahim M. Ghayad, Madiha Shoeib, Taha Matter, Huda M. Hussain, Enhancing corrosion resistance of stainless steel 304 using laser surface treatment, Key Engineering Materials, 384, 2008, 157-183

C. Tassin, F. Laroudie, M. Pons, L. Lelait, Improvement of the wear resistance of 316L stainless steel by laser surface alloying, Surface Coatings and Technology, 80(1-2), 1996, 207-210

V. Agarwala, K. G. Satyanarayana, R. C. Agarwala, R Garg, A study on the development and wear characteristics of rheocast Al-5Cu-2Pb alloy and Al-5Cu/Pb-18Sn wire composites, Materials Science and Engineering A 327 (2), 2002, 186-202