Journal Press India^®

Author Details ( * ) denotes Corresponding author

The various components where composites can replace conventional metals in automobiles have been discussed in the following paragraphs. The components discussed are the drive shaft, brake rotor, engine valves, body and suspension. Each component the composite used to replace is different from other components because of the specific work carried by each individual component. The final comparison of the composite to the conventional metal in each material showed evident weight reduction and improved efficiency.

Keywords

Composite: Automobile: Weight Reduction: Efficiency.

1. DG Lee, HS Kim. Optimal design of the press fit joint for a hybrid aluminum/composite drive shaft, Composite Structures, 70, 2005, 33-47.


2. SA Mutasher. Prediction of the torsional strength of the hybrid aluminum/composite drive shaft, Materials and Design, 30, 2009, 215-220.


3. H Al-Qureshi. Automobile leaf spring form composite materials, Journal of material processing technology, 118,2001, 58-61.


4. DG Lee, SW Lee. Composite hybrid valve lifter for automotive engines, Composite Structures, 71, 2005, 26-33.


5. G Savage M Oxley. Repair of composite structures on Formula 1 race cars, Engineering Failure Analysis, 17, 2010, 70-82.


6. YG Zhao, W Zhou, QD Qin. Dry sliding wear behavior of Mg2Si/Al composites against automobile friction material, Wear, 264, 2008, 654-661.


7. A Daoud, MT AbouEl-khair. Wear and friction behavior of sand cast brake rotor made of A359-20vol%SiC particle composites sliding against automobile friction material, Tribology International, 43, 2010, 544-553.


8. DH Cho, DG Lee, JH Choi. Manufacturing of one-piece automotive driveshafts with aluminum and composite materials, Compos Struct, 38, 1997, 309-319, 1997.


9. LD Lee. Optimal design of the adhesively-bonded tubular single lap joint, J Adhesion, 50, 1995, 165-80.


10. C Ruegg, J Habermeier. Composite propeller shafts design and optimization, Advance in Composite Materials, Proceeding of the third International Conference on Composite Materials, Paris, 1980.


11. G Belingardi, G Genta, P Campagna. Hybrid composite technology for automotive drive shaft, a Computer Aided Optimization, Proc. ISATA 85 Conference, Graz, Austria, 1985.


12. DH Cho, DG Lee. Manufacturing of co-curing aluminum composite shafts with compression during co-curing operation to reduce residual thermal stresses, J Compos Mater, 32, 1998, 1221-41.


13. DH Cho, DG Lee. Manufacturing of co-curing aluminum composite shafts with compression during co-curing operation to reduce residual thermal stresses, J Compos Mater , 32, 1998, 1221-41.


14. P Beardmore. Composite structures for automobiles, Compos Struct, 5, 1986, 163-76.


15. T Okuma. Brief view over technologies for fuel economy and weight reduction, Soc Automot Eng Jpn, 37(8), 1983, 862-9.


16. SS Cheon, JH Choi, DG Lee. Development of the composite bumper beam for passenger cars, Compos Struct, 32, 1995, 491-9.


17. J Bijwe, J Indumathi, BK Satapathy, AK Ghosh. Influence of carbon fabric on fretting wear performance of polyetherimide composite, Tribol, 124, 2002, 834-9.


18. JC Walker, WM Rainforth, H Jones. Lubricated sliding wear behavior of aluminum alloy composites, Wear, 259, 2005, 577-89.


19. A Ravikiran. Effect of pin specimen contact length in the sliding direction on tribological results of pin-on-disc tests, Tribology Letter, 4, 1998, 49-58.


20. G Straffelini. A simplified approach to the adhesive theory of friction, Wear, 249, 2001, 79-85.